Rotary N375 EQUALIZER CABLE S10IEH2

Rotary
Rotary-N375 Class B - See Terms

$179.40

Class B - See Terms

No reviews have been submitted for this product



Rotary Lift Replacement Cables

34’ 3-3/16” Long EQUALIZER CABLE S10IEH2

5/16" Diameter Cable

Fits Models: Rotary Lift Models SPO10, S10i-EH2 (Extended Height 2’), S10iP, S10iB


Overall Length: 34’ 3-3/16” Long (10444.16 mm)

Cable Diameter: 5/16” (7.938 mm)

Cable Material: Galvanized Steel

Cable Ends: (2) Threaded Studs 5/8”-11


Content Listing:


(1) Wire Rope Cable Assembly


Alternative nomenclature or also known as:

Wire Rope Balancing Cable

Wire Rope Equalizing Cable

Wire Rope Equalizer Cable

Wire Rope Stabilizer Cable

Wire Rope Synchronizing Cable

Wire Rope Cable Assembly

Wire Rope Cables

Uses: Auto Lifts, Car Lifts, Light Truck Lifts, Vehicle Lifts, Van Lifts, Bus Lifts

Fits Models:

  • FJ5149
  • FJ5158
  • FJ5198
  • S10IN6G7
  • S10IN6T7
  • SPO10EH2
  • SPO10E522
  • SPO10E552
  • SPO10E5G7
  • SPO10E5T7
  • SPO10E707
  • SPO10F5G7
  • SPO10L5G7
  • SPO10N522
  • SPO10N552
  • SPO10N5G7
  • SPO10N5T7
  • SPO10N707
  • SPO10U5G7
  • SPO10U5T7
  • SPO10U707
  • SPO40MD587
  • TLO7E567
  • TLO7N567

Let us help you find the correct cables the first time. The Make, Model and Configuration of your lift will change the cables used on your specific lift.

    Please contact us with the following information:
  • Brand of Lift
  • Full Model Number of Lift
  • Height of the Columns
  • Width of the Lift [ measured outside of base plate to outside of the other base plate ]
  • The types of ends on your cable; i.e. 2 threaded ends, 2 button ends, etc
  • Diameter of Cable. put a wrench on the cable itself to verify diameter needed. There are a few oddballs out there and this will save you a lot of frustration and downtime.

* If you do not know the Brand and/or Model of your lift, don't worry. Just get the remainder of the information. We will email you a cable worksheet to fill out and we can get it matched up that way.


Safety First: Replace Auto Lift Cables at First Sign of Wear


All wire rope cables generally wear both from the inside and outside. Inside wear is much less significant and is caused as the cables are pulled across the cable pulleys or sheaves. This wear is caused by what is termed nicking and can appear on internal strands with an almost scalloped look. External wear on cables is much more apparent and is essentially abrasive wear. Abrasive wear is the result of metal being slowly worn away or removed over time. This appears on the crowns of each wire with a flattening of the wire appearance. As the wires flatten, material is being lost. Since the strength of the cable continues to lessen, the cable becomes weaker. Additionally, almost everyone at some point has seen frayed rope. This is a condition where unraveling, worn, or separated strands become evident. If this is observed to be happening on any wire rope cable assembly, immediately cease use of the equipment with this type of worn cable and replace the cable as well as the sheaves or pulleys immediately.


As a rule, if you own an auto lift or anything that uses wire rope cables, you should at a minimum conduct monthly visual inspection of the cables and sheaves or pulleys. This is especially important if your cable-driven equipment is frequently used. If you are starting to witness the small round strands comprising each cable assembly starting to flatten and then even flatter, it is time to consider replacing the affected cables. Most cables on auto lifts or even any equipment including winches are easy to replace and the costs are relatively minimal. If you do not wish to replace the cable assembly yourself, there are many companies that specialize in auto lift installation and service that can help you.



Please note many cables are Special Order and are not eligible for Returns/Refunds or Exchanges. We want to make sure you get the right cables the first time and are not stuck with cables that will not work for you.

All Rotary parts Ship direct from the factory. All Rotary parts orders have a minimum order of $100.00. Additional ship time and charges will apply if the minimum order is not met.


There aren't any reviews for this product.


Related Products


Categories

Back to top
Welcome to the newly designed website. You can still find all of our great inventory in our shop. If you have any problems, please feel free to contact us.